av免费在线-av免费在线播放网址-av免费在线观看的网址-av免费在线观看一区二区三区-av喷水高潮喷水在线观看-av喷水高潮喷水在线观看c

阻燃防火材料-網上貿易平臺 | | WAP瀏覽
服務熱線:4006555305
當前位置: 首頁 » 防火測試中心 » 各國標準法規 » 美國 » 正文

ASTM E1317船舶表面終飾材易燃性試驗方法

放大字體  縮小字體 發布日期:2012-02-08   瀏覽次數:69  分享到: 分享到騰訊微博
ASTM E1317船舶表面終飾材易燃性試驗方法
ASTM E1317 Standard Test Method for Flammability of Marine Surface Finishes
ASTM E1317船舶表面終飾材易燃性試驗方法

This test method provides a means for evaluation of the flammable performance of surface finish materials used in constructing and outfitting ships.
A specimen of the surface finish of concern is mounted on the support material contemplated for use and subjected to a controlled significant radiant-flux exposure.
All specimens are tested while mounted in a vertical plane.
The following surfaces are exposed to test:
Bulkhead specimens having surface veneers, fabrics, or painted finishes are tested on one or both exposed sides.
Ceiling finish materials shall be tested on the lower exposed surface.
For ceiling finish materials which are perforated and air backed, tests also shall be conducted on the back (upper) surface of the material.
Deck finish and flooring materials are tested on the upper exposed surface.
Protective membranes or finishes on insulation materials are tested on the air-exposed face or faces.
This test method provides fire properties that relate to the flammability of the specimens tested. These include ignitability, heat exposure for continued burning, critical flux at extinguishment, and heat-release behavior under varying flux-exposure conditions applied.
This test method does not provide:
Full information on fire properties of surface-finish materials supported by backing materials other than those tested.
Full information on surface-finish materials when used in other thicknesses than those tested.
Methods for using the fire property measurements as a measure for classifying the fire risk or hazard of the specimens tested.
1. Scope
1.1 This fire-test-response standard covers a procedure for measuring fire properties associated with flammable behavior of surface finishes used on noncombustible substrates aboard ship (Note 1). In particular, these include surface finishes intended for use in ship construction such as deck surfacing materials, bulkhead and ceiling veneers including any adhesives used to fasten the veneers to the bulkheads and ceilings, paints, and exposed treatment of insulating materials.
Note 1—This test method has been prepared to closely follow the test procedure of IMO Resolution A.653(16) (1). Optional provisions not applicable to the domestic use of this test method have been deleted.
1.2 Tests performed according to this test method are intended to yield fire properties that, when appropriately interpreted, are potentially useful to select materials and surface treatments that will limit the rapid growth and spread of fire.
1.3 This test method requires a specific range of specimen radiant thermal exposure for measuring fire properties.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.

2. Referenced Documents (purchase separately)
ASTM Standards
E84 Test Method for Surface Burning Characteristics of Building Materials
E162 Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
E176 Terminology of Fire Standards
E286 Method of Test for Surface Flammability of Building Materials Using an 8-ft (2.44-m) Tunnel Furnace
E648 Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source
E970 Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source
E1321 Test Method for Determining Material Ignition and Flame Spread Properties
Code of Federal Regulations (CFR)
CFRTitle46, Part 164.009, Noncombustible Materials
Index Terms
Adhesives; Bulkheads; Calibration--flammability analysis instrumentation; Ceiling veneers; Decks; Fire testing--building materials; Flammability--building materials; Heating tests--building products; Ignition--rubber/cellular materials; Marine environments; Noncombustible substrates; Pyrometer; Total radiation pyrometer;
 

  詳情請咨詢
  防火資源網-阻燃防火測試中心
  電話:(+86)0592-5056213
  傳真:(+86)0592-5105807
  郵件:firetest@firetc.com

凡注明"防火資源網"的所有作品,由<防火資源網>整理編輯,任何組織未經<防火資源網>及其擁有者授權,不得復制、轉載、摘編或利用其它方式應用于任何商業行為。

 
 
[ 防火測試中心搜索 ]  [ ]  [ 告訴好友 ]  [ 打印本文 ]  [ 關閉窗口 ]  [ 返回頂部 ]

 

 
 
推薦防火測試
推薦圖文
點擊排行
 
 
網站首頁 | 廣告服務 | 關于我們 | 聯系方式 | 服務協議 | 版權聲明 | 網站地圖 | 友情鏈接 | 網站留言 | 舊版本 | 閩ICP備09009213號
?2019-2021 FIRETC.COM All Rights Reserved ? 備案號:閩ICP備09009213號-1在線客服 點擊QQ交談/留言 點擊QQ交談/留言
主站蜘蛛池模板: 亚洲AV无码男男A片在线观看 | 亚洲成人一区二区 | 一本久道综合在线无码人妻 | 99久久精品国产成人综合 | 精品午夜福利在线观看 | 精品视频一区二精品视频一 | 欧美激情a∨在线视频播放 欧美激情A片久久久久久 | 在线一区二区三区 | 国产真实野战在线视频 | 桃色播播 | 乱伦精品综合免费 | 自拍偷自拍亚洲精品偷一 | 小明永久成人一区二区 | 精品少妇人妻av一区二区三区 | 无遮挡无码视频在线播放互动交流 | 加勒比久久综合久久鬼色88 | 成人免费视频一区二区 | 最新国产毛2卡3卡4卡 | 成人做受视频试看60秒 | 精品日韩午夜电影在线看 | 亚洲制服丝袜中 | 亚洲精品国产自在现线最新 | 中文欧美一区二区精品 | 凶猛办公室高清在线观看免费 | 丝袜中文字幕人妻中处 | 国产免费a∨片在线软件 | 宅男噜噜噜国产在线观看 | 2025天堂中文字幕一区在线观 | 最好韩国日本高清免费 | 精品少妇爆乳无码av无码专区 | 无码午夜在线观看 | 亚洲精品亚洲人成人网 | 成 人毛茸茸的视频 | 国产在线观看清码视频 | 久久久无码人妻精品无码 | 亚洲欧美另类中文字幕 | 一本大道香蕉青青久久 | 一本加勒比hezyo无码资源网 | 亚洲欧美日韩国产另类一区二区三区 | 另类欧美日 | 久久综合精品二区无码 |