ASTM E2188 Standard Test Method for Insulating Glass Unit Performance
ASTM E2188絕緣玻璃部件性能的標準試驗方法
This test method is intended to provide a means for testing the performance of the sealing system and construction of sealed insulating glass units.
Sealed insulating glass units tested in accordance with this method may be suitable for structurally glazed applications. However, factors such as sealant longevity when exposed to long term ultraviolet light and the structural properties of the sealant must be reviewed for these applications.
Sealed insulating glass units tested in accordance with this method are not intended for continuous exposure to high relative humidity conditions or long-term immersion in water.
1. Scope
1.1 This test method covers procedures for testing the performance of preassembled permanently sealed insulating glass units or insulating glass units with capillary tubes intentionally left open.
1.2 This test method is applicable only to sealed insulating glass units that are constructed with glass.
1.3 This test method is applicable to both double-glazed and triple-glazed insulating glass units. For triple-glazed insulating glass units where both of the outer lites are glass and the inner lite is either glass or a suspended film.
1.4 The unit construction used in this test method contains dimensions that are an essential component of the test. Different types of glass, different glass thicknesses, and different airspace sizes may affect the test results.
1.5 This test method is not applicable to sealed insulating glass units containing a spandrel glass coating due to testing limitations.
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately)
ASTM Standards
C162 Terminology of Glass and Glass Products
C717 Terminology of Building Seals and Sealants
C1036 Specification for Flat Glass
E546 Test Method for Frost/Dew Point of Sealed Insulating Glass Units
E631 Terminology of Building Constructions
E2190 Specification for Insulating Glass Unit Performance and Evaluation
Index Terms
IGU performance; IGU seal durability; insulating glass units (IGU); sealed insulating glass units; Sealed insulating glass units; IGU seal durability; Insulating glass (IG); Performance--glass materials/applications;
ASTM E2188絕緣玻璃部件性能的標準試驗方法
This test method is intended to provide a means for testing the performance of the sealing system and construction of sealed insulating glass units.
Sealed insulating glass units tested in accordance with this method may be suitable for structurally glazed applications. However, factors such as sealant longevity when exposed to long term ultraviolet light and the structural properties of the sealant must be reviewed for these applications.
Sealed insulating glass units tested in accordance with this method are not intended for continuous exposure to high relative humidity conditions or long-term immersion in water.
1. Scope
1.1 This test method covers procedures for testing the performance of preassembled permanently sealed insulating glass units or insulating glass units with capillary tubes intentionally left open.
1.2 This test method is applicable only to sealed insulating glass units that are constructed with glass.
1.3 This test method is applicable to both double-glazed and triple-glazed insulating glass units. For triple-glazed insulating glass units where both of the outer lites are glass and the inner lite is either glass or a suspended film.
1.4 The unit construction used in this test method contains dimensions that are an essential component of the test. Different types of glass, different glass thicknesses, and different airspace sizes may affect the test results.
1.5 This test method is not applicable to sealed insulating glass units containing a spandrel glass coating due to testing limitations.
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately)
ASTM Standards
C162 Terminology of Glass and Glass Products
C717 Terminology of Building Seals and Sealants
C1036 Specification for Flat Glass
E546 Test Method for Frost/Dew Point of Sealed Insulating Glass Units
E631 Terminology of Building Constructions
E2190 Specification for Insulating Glass Unit Performance and Evaluation
Index Terms
IGU performance; IGU seal durability; insulating glass units (IGU); sealed insulating glass units; Sealed insulating glass units; IGU seal durability; Insulating glass (IG); Performance--glass materials/applications;
