ASTM D6448 Standard Specification for Industrial Burner Fuels from Used Lubricating Oils
ASTM D6448來自用過的潤滑油的工業(yè)燃燒器燃料的標準規(guī)范
This specification covers four grades of fuel oil made in whole or in part with hydrocarbon-based used or reprocessed lubricating oil or functional fluids, such as preservative and hydraulic fluids. Grades RFO4, RFO5L, RFO5H, and RFO6 are of increasing viscosity and are intended for use in various types of fuel-oil-burning industrial equipment under various climatic and operating conditions, and are not intended for use in residential heaters, small commercial boilers, combustion engines, or marine applications. Detailed requirements for each grade of lubricating oil shall be tested accordingly, and are as follows: viscosity; flash point; water and sediment content; pour point; density; ash content; sulphur content; extracted pH; and gross heating value.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers four grades of fuel oil made in whole or in part with hydrocarbon-based used or reprocessed lubricating oil or functional fluids, such as preservative and hydraulic fluids. The four grades of fuel are intended for use in various types of fuel-oil-burning industrial equipment under various climatic and operating conditions. These fuels are not intended for use in residential heaters, small commercial boilers, combustion engines, or marine applications,
1.1.1 Grades RFO4, RFO5L, RFO5H, and RFO6 are used lubricating oil blends, with or without distillate or residual fuel oil, or both, of increasing viscosity and are intended for use in industrial burners equipped to handle these types of recycled fuels.
Note 1—For information on the significance of the terminology and test methods used in this specification, see Appendix X1.
1.2 This specification is for use in contracts for the purchase of fuel oils derived from used lubricating oil and for the guidance of consumers of such fuels. This specification does not address the frequency with which any particular test must be run.
1.3 Nothing in this specification shall preclude observance of national or local regulations, which can be more restrictive. In some jurisdictions, used oil is considered a hazardous waste and fuels from used oil are required to meet certain criteria before use as a fuel.
Note 2—For United States federal requirements imposed on used oil generators, transporters and transfer facilities, reprocessors, marketers, and burners, see 40 CFR 279.
Note 3—The generation and dissipation of static electricity can create problems in the handling of distillate burner fuel oils. For more information on the subject, see Guide D 4865.
1.4 The values stated in SI units are to be regarded as standard; non-SI units, when given, are for information only.
2. Referenced Documents (purchase separately)
ASTM Standards
D56 Test Method for Flash Point by Tag Closed Cup Tester
D93 Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
D95 Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
D96 Test Method for Water and Sediment in Crude Oil by Centrifuge Method Field Procedure
D97 Test Method for Pour Point of Petroleum Products
D129 Test Method for Sulfur in Petroleum Products (General Bomb Method)
D240 Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter
D396 Specification for Fuel Oils
D445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
D473 Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction Method
D482 Test Method for Ash from Petroleum Products
D1217 Test Method for Density and Relative Density (Specific Gravity) of Liquids by Bingham Pycnometer
D1250 Guide for Use of the Petroleum Measurement Tables
D1266 Test Method for Sulfur in Petroleum Products (Lamp Method)
D1298 Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
D1480 Test Method for Density and Relative Density (Specific Gravity) of Viscous Materials by Bingham Pycnometer
D1481 Test Method for Density and Relative Density (Specific Gravity) of Viscous Materials by Lipkin Bicapillary Pycnometer
D1552 Test Method for Sulfur in Petroleum Products (High-Temperature Method)
D1796 Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
D2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
D2709 Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
D2983 Test Method for Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer
D3245 Test Method for Pumpability of Industrial Fuel Oils
D3828 Test Methods for Flash Point by Small Scale Closed Cup Tester
D4052 Test Method for Density and Relative Density of Liquids by Digital Density Meter
D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D4175 Terminology Relating to Petroleum, Petroleum Products, and Lubricants
D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products
D4294 Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
D4377 Test Method for Water in Crude Oils by Potentiometric Karl Fischer Titration
D4865 Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems
D4868 Test Method for Estimation of Net and Gross Heat of Combustion of Burner and Diesel Fuels
D4980 Test Methods for Screening of pH in Waste
D5185 Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
D6304 Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration
D6450 Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester
D6822 Test Method for Density, Relative Density, and API Gravity of Crude Petroleum and Liquid Petroleum Products by Thermohydrometer Method
D7042 Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
D93 Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
D95 Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
D96 Test Method for Water and Sediment in Crude Oil by Centrifuge Method Field Procedure
D97 Test Method for Pour Point of Petroleum Products
D129 Test Method for Sulfur in Petroleum Products (General Bomb Method)
D240 Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter
D396 Specification for Fuel Oils
D445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
D473 Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction Method
D482 Test Method for Ash from Petroleum Products
D1217 Test Method for Density and Relative Density (Specific Gravity) of Liquids by Bingham Pycnometer
D1250 Guide for Use of the Petroleum Measurement Tables
D1266 Test Method for Sulfur in Petroleum Products (Lamp Method)
D1298 Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
D1480 Test Method for Density and Relative Density (Specific Gravity) of Viscous Materials by Bingham Pycnometer
D1481 Test Method for Density and Relative Density (Specific Gravity) of Viscous Materials by Lipkin Bicapillary Pycnometer
D1552 Test Method for Sulfur in Petroleum Products (High-Temperature Method)
D1796 Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
D2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
D2709 Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
D2983 Test Method for Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer
D3245 Test Method for Pumpability of Industrial Fuel Oils
D3828 Test Methods for Flash Point by Small Scale Closed Cup Tester
D4052 Test Method for Density and Relative Density of Liquids by Digital Density Meter
D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D4175 Terminology Relating to Petroleum, Petroleum Products, and Lubricants
D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products
D4294 Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
D4377 Test Method for Water in Crude Oils by Potentiometric Karl Fischer Titration
D4865 Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems
D4868 Test Method for Estimation of Net and Gross Heat of Combustion of Burner and Diesel Fuels
D4980 Test Methods for Screening of pH in Waste
D5185 Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
D6304 Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration
D6450 Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester
D6822 Test Method for Density, Relative Density, and API Gravity of Crude Petroleum and Liquid Petroleum Products by Thermohydrometer Method
D7042 Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
U.S. Environmental Protection Agency Standards
EPASW-846Method9056 Determination of Inorganic Anions by Ion Chromatography
Federal Code of Regulations Standards
40CFR279 Standards for the Management of Used Oil
Index Terms
burner fuels; fuel oils; furnace oils; petroleum and petroleum products; specifications; used oils; Burner fuel oils--specifications; Fuel oils--specifications; Furnace oils; Industrial petroleum products--specifications; Lubricating oils--specifications; Petroleum products--specifications; Used lubricating oils ;
